Name: 7.5 x 7.5 ft. Lumiere Light Wall® Backlit Single-Sided (Graphic Package)
Brand: DG Creativ LLC
Price: 2502.0 USD
Availability: InStock

A square lit wall, 7.5 feet on each side, for a 10x10 booth where the whole back should light up rather than carry a lightbox hung in the middle of a dark wall. Three LED ladder light sets sit inside the 14.5 in. frame behind a backlit fabric face and a blockout panel, so the print reads evenly instead of showing the lamps. One person puts it together in about 25 minutes, and it travels in two cartons rather than a crate.

Key Features

• Lit from inside the frame: three 1x3 LED ladder light sets wash the graphic from behind. No clamp lights reaching over the top of the display, and no lighting rig to rent.

• Borderless SEG finish: the graphic has a silicone bead sewn into its edge that tucks into the channel bars, so the fabric pulls flat and the frame disappears behind it.

• Square format: 88.75 in. on both sides, so the lit face reads the same whether the booth is seen straight on or down the aisle.

• One person, about 25 minutes: the frame pops open by hand and the eight channel bars clip on. No tools.

• Fits the hard case option: the hard case holds one frame with its bag, the channel bars with their bags and a full set of ladder lights with transformers and clips, for frame sizes up to 10 x 7.5 ft. This frame is inside that limit.

• End caps plain or printed: non-printed end caps are included. Printed caps carry artwork around the 14.5 in. sides, which is what the depth is worth using for.

Specifications

Assembled size: 88.75 in. W x 88.75 in. H x 14.5 in. D
Graphic size: 88 in. W x 88 in. H
Frame: collapsible pop-up frame with eight 3-section SEG channel bars
Lighting: three 1x3 LED ladder light sets with transformers and power cords
Graphic material: dye-sublimated backlit stretch fabric with a silicone edge, over a blockout panel
Frame carton: 34 in. x 14 in. x 9 in., 36 lbs including graphics
Light carton: 30.5 in. x 7.5 in. x 5.5 in., 24 lbs
Total shipped: two cartons, 60 lbs
Setup: one person, about 25 minutes

What's Included

(1) Pop-up frame with carry bag
(8) 3-section channel bars with bag
(3) 1x3 LED ladder light sets with travel bags, (3) transformers and (3) power cords
(1) 7.5 x 7.5 ft. backlit graphic
(1) 7.5 x 7.5 ft. blockout panel
(2) end caps, non-printed; printed end caps available

Shipping

Shipping on this display is quoted at checkout. It goes out as two cartons totaling 60 lbs — a 34 x 14 x 9 in. frame case and a 30.5 x 7.5 x 5.5 in. light case. Both move by ground parcel, so there is no crate, no freight bill and no liftgate to arrange.

What you need at the venue

Floor space: 88.75 in. of width and 14.5 in. of depth against the back wall of a 10 ft. booth, which leaves roughly a foot of width to spare on each side.
Power: one standard outlet. Budget for a single power drop at the booth; the transformers do not need a dedicated circuit.
Height clearance: 88.75 in. assembled, under the 8 ft. back-wall limit most inline booths are held to. Check your own exhibitor kit, because the limit is set per show.
Labor: one person, no tools. In a union exhibit hall the kit says who may set it up, and that rule applies to a hand-assembled pop-up as much as to a crated build.

Please check your show guidelines to confirm this configuration conforms to the regulations for your space. If it has to change to conform, email sales@dgcreativ.com and we will quote a custom configuration rather than ship you something the hall will not let you build.

Where a 7.5 ft. square wall fits

Inside the hall it is the back wall of a 10x10 inline booth on its own, with room at the sides for a counter or a monitor stand. Two of them side by side build a lit 15 ft. run.

Outside the hall it holds up where the frame stays and the message changes: lobby and reception walls, showroom and dealership displays, clinic wayfinding, retail entrances, and hotel and conference registration areas. The graphic is reprinted for the next campaign and the frame stays where it is.

Ordering from Stow, Ohio

Backlit graphics are not ordinary prints — density and contrast behave differently when light passes through the fabric instead of bouncing off it. We lay out the artwork, proof it, and say plainly if a logo or a photograph will wash out once it is lit.

For customers across Northeast Ohio — Akron, Cleveland, Canton, Kent, Hudson, Youngstown — we can deliver the wall, set it up at the venue and store it between shows, then reprint the graphic for the next one. Outside the region it ships in its two cases. Call 330.968.0678, email sales@dgcreativ.com, or request a quote.

Frequently Asked Questions

How many lights does the square frame take?
Three 1x3 ladder light sets, each with its own transformer and power cord. They mount on one side of the frame only.

This is the single-sided package. What does that mean I get?
One backlit graphic on the front and a blockout panel behind it. The blockout is what keeps the output even across the face instead of letting light escape out the back.

Can I reprint just the graphic later?
Yes. The frame, channel bars and lights are the investment and last for years. Send new artwork and we print a replacement backlit graphic to the same 88 x 88 in. layout.

What is the difference between the end cap options?
Non-printed end caps close off the 14.5 in. sides in solid fabric. Printed end caps carry your artwork around those edges, so the branding continues when the display is seen from an angle in the aisle.

Does it need a special power supply?
No. The transformers plug into a standard outlet.

Will the hard case hold everything?
Yes. The hard case option covers frame sizes up to 10 x 7.5 ft., and this frame is inside that.

7.5 x 7.5 ft. Lumiere Light Wall® Backlit Single-Sided (Graphic Package)