Name: 20 ft. Lumiere Light Wall® Configuration D Backlit
Brand: DG Creativ LLC
Price: 7849.0 USD
Availability: InStock

A straight 20-foot lit back wall: 236.2 in. wide, 88.6 in. high and only 14.5 in. deep, built from two 10 x 7.5 ft. frames joined with six straight connectors. Twenty-four LED ladder light sets light it from inside the aluminum, which is what lets the whole twenty feet read as one lit surface rather than two panels with a band of shadow between them.

At 88.6 in. tall it sits under the 96 in. back wall limit most shows set for inline spaces, and at 14.5 in. deep it gives up almost none of the booth.

Key Features

• One continuous lit surface: Twenty-four light sets across two frames, with the joint falling inside a channel bar rather than between two separate lit boxes. From the aisle it reads as a single twenty-foot graphic.

• Printed on both faces: Four main graphics, two to a face, plus two end cap graphics for the edges. The back face matters more than people expect in a 10x20 or an island, where the wall is seen from inside the booth as well.

• Borderless SEG finish: Each graphic has a silicone bead sewn around its perimeter that tucks into the channel bars, so the fabric pulls flat and the frame disappears behind it.

• Shallow footprint: 14.5 in. deep. A lit wall this wide usually means a lightbox that eats a foot and a half of floor; this one does not.

• Tool-free: The frames pop open by hand, the channel bars clip on and the light brackets are already positioned. Nothing needs a wrench.

• Reprint the fabric, keep the frame: The frames, bars and lights are the long-term purchase. New artwork means new backlit fabric printed to the same panel sizes.

Specifications

Assembled size: 236.2 in. W x 88.6 in. H x 14.5 in. D
Graphic sizes: 118.5 x 89 in. main panels; 14.25 x 89 in. end caps
Frames: two Lumiere pop-up frames, 10 x 7.5 ft., joined with six straight connectors
Lighting: twenty-four LED ladder light sets with eight transformers, supplied
Graphic material: UV backlit fabric, dye-sublimated
Finishing: SEG, silicone beading sewn around the perimeter of the fabric
Shipped as: two cartons, each 34 x 14 x 9 in. and 39 lbs, 78 lbs in total
Setup: tool-free; allow two people and most of an hour at this width

What's Included

(4) main graphics, two front and two back
(2) end cap graphics
(2) pop-up frames, 10 x 7.5 ft., with carry bags
(8) 3-section channel bars, (8) 4-section channel bars and (4) end cap channel bars, with (2) channel bar bags
(6) straight connectors
(24) LED ladder light sets with (8) transformers
(2) transformer power cords and (8) male/female transformer connector cords
(32) middle light brackets and (32) top and bottom light brackets

Shipping

Shipping on this display is quoted at checkout. It is not in our free ground shipping group. It goes out as two cartons of 34 x 14 x 9 in., 39 lbs each, 78 lbs in total.

What you need at the venue

A 20 ft. run of back wall and 14.5 in. of depth
Power at the booth. Eight transformers are supplied with eight male/female connector cords and two transformer power cords, so the light sets chain together and come back to two plugs
No tools, and no ladder for most people at 88.6 in.
Two people and most of an hour. The light sets and their brackets, not the frames, are what take the time

Where a 20 ft. lit wall fits

This is the back wall for a 10x20 inline booth, and the shallow depth leaves room for counters, a monitor and seating in front of it. In a 20x20 island it works as a spine down the middle, since both faces are printed.

Away from the exhibit hall, a lit twenty-foot wall holds up as a permanent fixture: lobby and atrium branding, showroom walls, arena and field house concourses, hospital and clinic entrances, and conference registration. The graphic changes with the campaign; the frame stays on the wall.

Ordering from Stow, Ohio

A twenty-foot graphic spread across two panels is a layout problem before it is a print problem. The seam has to fall somewhere forgiving, type has to be sized for a sixty-foot reading distance, and backlit fabric flattens contrast because the light comes through it rather than off it. We set the artwork up, proof it, and say plainly when a logo or a photograph will not hold once it is lit.

For customers across Northeast Ohio — Akron, Cleveland, Canton, Kent, Hudson, Youngstown — we can deliver the wall, set it up at the venue, store it between shows and reprint the graphics for the next one. Outside the region it ships in its two cases.

Show rules vary. Check your show's guidelines before ordering, and if the configuration has to change to meet them, email sales@dgcreativ.com and we will quote the change.

Frequently Asked Questions

Are the lights included?
Yes. Twenty-four LED ladder light sets, eight transformers, the connector cords and all the light brackets are in the package. Nothing else is needed to light it.

How many outlets will I need?
The eight transformers chain together through the supplied connector cords and run back to two power cords. Order a power drop for the booth and tell us if you need the exact outlet count confirmed for your show in writing.

Will the two panels show a seam?
There is a channel bar where the frames meet, so you see a thin vertical line rather than a dark band. Artwork can be laid out so the join falls in a quiet part of the graphic.

Will it pass my show's height rule?
At 88.6 in. it is under the 96 in. inline limit most shows use. Confirm against your own exhibitor kit.

Can I reprint just the graphics later?
Yes. Send new artwork and we print replacement backlit fabric to the same panel sizes. The frames, bars and lights stay.

20 ft. Lumiere Light Wall® Configuration D Backlit