10 ft L-Shape Lumiere Light Wall® Configuration B No Lights Single-Sided

A corner wall at normal booth height rather than the near-ten-foot height of Configuration A. Two frames — 10 x 7.5 ft and 7.5 x 7.5 ft — join with three L-connectors to turn the corner, carrying four main graphics, two per wall front and back, plus two end cap graphics, all 89 inches high. Supplied unlit; clamp lights can be added to light it from the front. Ships in two boxes at 35 lbs each, 70 lbs total, and each frame goes up in 5 to 10 minutes. Shipping on this item is quoted at checkout.

This is a corner product. An L-shape only works where both faces have somewhere to be seen: a corner booth, a peninsula, or a lobby or atrium where people approach from two directions. Drop it into a plain inline booth and the short leg points at the neighbor's back wall, which is 7 ft 5 in. of graphic nobody sees. If your space is a straight 10x10 or 10x20, a flat wall is the better buy — see the 10 x 10 ft. no-lights wall or the 20 x 7.5 ft. lit wall.

Which booth this fits

• Face widths: the long wall's graphic is 118.5 in. across, about 9 ft 10 in.; the short wall's is 89 in., about 7 ft 5 in. Allow roughly ten feet along one side and seven and a half along the other.
• Height: 88.6 in., under the 96 in. that most shows allow for a back wall, so this normally needs no height approval. Configuration A is the taller version and usually does.
• Depth of the frame itself: 14.5 in.
• Unlit by design. It arrives with no lights. That is the right choice under good venue lighting, or where the budget goes into the graphic rather than the hardware.

Lumiere Light Wall® 10 ft. L-Shape Frontlit Graphic Package (Configuration B) Includes:

• (4) Main Graphics - 2 Front, 2 Back
• (2) End Cap Graphics
• (2) Pop Up Frames (10 ft. x 7.5 ft & 7.5 ft. x 7.5 ft.)
• (4) 4-Section Channel Bars
• (10) 3-Section Channel Bars
• (8) End Cap Channel Bars
• (2) Channel Bar Bags
• (2) Carry Bags (for frame)
• (3) L-Connectors

Graphic Dimensions: 118.5" W x 89" H (2 Main), 89"W x 89"H (2 Main) & 14.25" W x 89" H (ECG)
Graphic Material: Stretch Fabric
Finishing: SEG (Silicone Edge Graphics) Silicone Beading sewn around the perimeter of the fabric
Display Height: 88.6"
Frame Depth: 14.5"
Assembled Footprint: confirmed with you before production — see the note below
Shipping Weight: 70 lbs (35 lbs per box)
Shipping Dimensions: 34" L x 14" W x 9" H (each box)

A note on the footprint: the overall assembled dimension published for this configuration repeats the figure for the straight 20 ft. wall, which does not match a two-frame L-shape with three L-connectors. Rather than publish a footprint we cannot stand behind, we confirm the exact assembled dimensions with you before production. Email sales@dgcreativ.com if you need them to plan a space.

What you need at the venue

• Floor space: about ten feet along one wall and seven and a half along the other, plus 14.5 in. of frame depth. Ask us for the confirmed assembled footprint before you commit to a layout.
• Power: none, unless you add lights. This is the one wall in the range that can go up in a booth with no electrical order at all.
• Crew: two people. Each frame goes up in 5 to 10 minutes, tool-free, and at 88.6 in. the top of the graphic is within reach without a ladder. Two people is our recommendation; the 5 to 10 minutes is the supplier's figure. Many convention centers require their own labor for exhibit setup, and the exhibitor manual says whether yours does.
• Getting it to the booth: two boxes at 35 lbs each, 70 lbs in total. No crate, so no dock, forklift or liftgate.
• Two open sides: confirm your booth is a corner or peninsula before ordering an L-shape.

Adding light later. The frames take clamp lights on the top channel. The Lumiere front-lit LED light is the matching fitting, and the rest of the family connects to it — a counter, a door, or a lit bridge. Lumiere only connects to Lumiere. See complete Lumiere booth systems.

Questions we get asked about this wall

Configuration A or Configuration B? Same L-shape, different height. Configuration A stands close to ten feet and usually needs show approval in inline space; this one is 88.6 in. and normally does not. If the booth is inline or you would rather not ask the show for anything, order this one.

Can I light it? Yes, with clamp lights on the top channel; the front-lit LED light is the matching fitting. If you want it lit from inside instead, the backlit walls in the range are built for that and this one is not convertible.

Will it work in a straight inline booth? Poorly. One leg ends up facing your neighbor's wall. Order a flat wall for inline space and keep the L-shape for corners and peninsulas.

What is the exact assembled footprint? We confirm it with you before production rather than publish it. The figure in the supplier data for this configuration repeats the one for the straight 20 ft. wall, which cannot be right for a two-frame L with three connectors, and a wrong footprint is how a booth layout fails on the day.

Does it need a dock or a forklift? No. Two boxes, 35 lbs each.

Can I reprint the graphics and keep the frames? Yes. The frames and channel bars are the part you keep; silicone edge fabric pushes in and out of the channel. Send us the show date and we will reprint from the file on record.

Can you set it up for us? In Northeast Ohio, yes — we are in Stow and we install at Cleveland and Akron venues. Outside that, many convention centers require their own labor for exhibit setup.

*Please check your tradeshow guidelines to make sure this configuration conforms to the show regulations. If adjustments to the configuration are required to meet the show requirements please contact us at sales@dgcreativ.com for a custom configuration quote*

Artwork and shipping. We send the print template and proof your file before it prints. Shipping on this item is quoted at checkout, or ask us to quote freight with your show details. DG Creativ is in Stow, Ohio: call 330.968.0678 or request a quote.